more devices

display.yml

@@ -0,0 +1,45 @@
+esphome:
+  name: display
+
+esp32:
+  board: esp32dev
+  framework:
+    type: arduino
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+  password: ""
+
+ota:
+  - platform: esphome
+    password: ""
+
+wifi:
+  ssid: "Cochrun"
+  password: "GreasyChicken784"
+
+  # Enable fallback hotspot (captive portal) in case wifi connection fails
+  ap:
+    ssid: "Display Fallback Hotspot"
+    password: "RUfAhbEfZmOU"
+
+captive_portal:
+
+psram:
+  mode: octal
+  speed: 80MHz
+    
+# Example minimal configuration entry
+display:
+  - platform: ili9xxx
+    model: ili9486
+    dc_pin: GPIOXX
+    reset_pin: GPIOXX
+    invert_colors: false
+    show_test_card: true
+    dimensions:
+      height: 320
+      width: 480

kitchen.yml

@@ -0,0 +1,102 @@
+esphome:
+  name: kitchen-sensor
+
+esp8266:
+  board: esp01
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+  password: ""
+
+ota:
+  - platform: esphome
+    password: ""
+
+wifi:
+  ssid: "Cochrun"
+  password: "GreasyChicken784"
+
+  # Enable fallback hotspot (captive portal) in case wifi connection fails
+  ap:
+    ssid: "Kitchen Fallback Hotspot"
+    password: "RUfAhbEfZmOU"
+
+captive_portal:
+    
+i2c:
+  sda: GPIO4
+  scl: GPIO5
+  scan: true
+  id: bus_a
+
+uart:
+  tx_pin: GPIO1
+  rx_pin: GPIO3
+  baud_rate: 115200
+
+sensor:
+  - platform: bme280_i2c
+    temperature:
+      name: "Temperature"
+      id: temperature
+    pressure:
+      name: "Pressure"
+      id: pressure
+    humidity:
+      name: "Humidity"
+      id: humidity
+    i2c_id: bus_a
+    address: 0x76
+
+dfrobot_sen0395:
+
+binary_sensor:
+  # Information coming from uart bus
+  - platform: dfrobot_sen0395
+    name: Mmwave UART
+
+    # on_...:
+    #   - dfrobot_sen0395.settings:
+    #       factory_reset: true
+    #       detection_segments:
+    #         # Define between one and four segments
+    #         - [0cm, 3m]
+    #         - [5.1m, 6.6m]
+    #         output_latency:
+    #           delay_after_detect: 0s
+    #           delay_after_disappear: 0s
+    #           sensitivity: 7
+
+  # Information coming from dedicated gpio (IO2)
+  - platform: gpio
+    name: Mmwave GPIO
+    device_class: motion
+    pin:
+      number: GPIO16
+      mode: INPUT_PULLDOWN
+
+switch:
+  # Switch to turn on/off detection
+  - platform: dfrobot_sen0395
+    type: sensor_active
+    name: Mmwave Active
+
+  - platform: dfrobot_sen0395
+    type: presence_via_uart
+    name: Mmwave UART active
+    restore_mode: always_on
+
+  - platform: dfrobot_sen0395
+    type: turn_on_led
+    name: Mmwave Led
+    restore_mode: always_off
+    icon: "mdi:led-on"
+
+  - platform: dfrobot_sen0395
+    type: start_after_boot
+    name: Mmwave Start
+    restore_mode: always_on
+

mmwave.yml

@@ -0,0 +1,65 @@
+esphome:
+  name: living-motion
+
+esp32:
+  board: upesy_wroom
+  framework:
+    type: arduino
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+  password: ""
+
+ota:
+  password: ""
+
+wifi:
+  ssid: "Cochrun"
+  password: "GreasyChicken784"
+
+  # Enable fallback hotspot (captive portal) in case wifi connection fails
+  ap:
+    ssid: "Living Motion Fallback Hotspot"
+    password: "VxKj9HWaXThv"
+
+captive_portal:
+    
+uart:
+  tx_pin: GPIO27
+  rx_pin: GPIO26
+  baud_rate: 115200
+
+dfrobot_sen0395:
+
+binary_sensor:
+  # Information coming from uart bus
+  - platform: dfrobot_sen0395
+    name: Mmwave UART
+
+  # Information coming from dedicated gpio (IO2)
+  - platform: gpio
+    name: Mmwave GPIO
+    device_class: motion
+    pin:
+      number: GPIO25
+      mode: INPUT_PULLDOWN
+
+switch:
+  # Switch to turn on/off detection
+  - platform: dfrobot_sen0395
+    type: sensor_active
+    name: Mmwave Active
+
+  # - platform: dfrobot_sen0395
+  #   type: turn_on_led
+  #   name: Mmwave Led
+  #   restore_mode: always_on
+  #   icon: "mdi:led-on"
+
+  # - platform: dfrobot_sen0395
+  #   type: start_after_boot
+  #   name: Mmwave Start
+  #   restore_mode: always_on