updates

thermostat.yml

@@ -2,7 +2,7 @@ esphome:
   name: thermostat
 
 esp32:
-  board: upesy_wroom
+  board: esp32dev
   framework:
     type: arduino
 
@@ -14,6 +14,7 @@ api:
   password: ""
 
 ota:
+  - platform: esphome
     password: ""
 
 wifi:
@@ -33,6 +34,11 @@ i2c:
   scan: true
   id: bus_a
 
+uart:
+  tx_pin: GPIO27
+  rx_pin: GPIO26
+  baud_rate: 115200
+
 sensor:
   - platform: bme280_i2c
     temperature:
@@ -40,20 +46,107 @@ sensor:
       id: temperature
     pressure:
       name: "Pressure"
+      id: pressure
     humidity:
       name: "Humidity"
+      id: humidity
     i2c_id: bus_a
     address: 0x76
 
+dfrobot_sen0395:
+
+binary_sensor:
+  # Information coming from uart bus
+  - platform: dfrobot_sen0395
+    name: Mmwave UART
+
+    # on_...:
+    #   - dfrobot_sen0395.settings:
+    #       factory_reset: true
+    #       detection_segments:
+    #         # Define between one and four segments
+    #         - [0cm, 3m]
+    #         - [5.1m, 6.6m]
+    #         output_latency:
+    #           delay_after_detect: 0s
+    #           delay_after_disappear: 0s
+    #           sensitivity: 7
+
+  # Information coming from dedicated gpio (IO2)
+  - platform: gpio
+    name: Mmwave GPIO
+    device_class: motion
+    pin:
+      number: GPIO25
+      mode: INPUT_PULLDOWN
 
 switch:
-  - platform: gpio
-    pin: 15
-    id: heater
+  # Switch to turn on/off detection
+  - platform: dfrobot_sen0395
+    type: sensor_active
+    name: Mmwave Active
+
+  - platform: dfrobot_sen0395
+    type: presence_via_uart
+    name: Mmwave UART active
+    restore_mode: always_on
+
+  - platform: dfrobot_sen0395
+    type: turn_on_led
+    name: Mmwave Led
+    restore_mode: always_on
+    icon: "mdi:led-on"
+
+  - platform: dfrobot_sen0395
+    type: start_after_boot
+    name: Mmwave Start
+    restore_mode: always_on
+
   - platform: gpio
     pin: 16
-    id: ac
+    id: heater
+    restore_mode: RESTORE_DEFAULT_OFF
   - platform: gpio
     pin: 17
+    id: ac
+    restore_mode: RESTORE_DEFAULT_OFF
+  - platform: gpio
+    pin: 15
     id: fan
+    restore_mode: RESTORE_DEFAULT_OFF
 
+climate:
+  - platform: thermostat
+    name: "Thermostat"
+    sensor: temperature
+    humidity_sensor: humidity
+    min_cooling_off_time: 10s
+    min_cooling_run_time: 10s
+    min_heating_off_time: 10s
+    min_heating_run_time: 10s
+    min_idle_time: 30s
+    cool_action:
+      - switch.turn_off: heater
+      - switch.turn_on: ac
+      - switch.turn_on: fan
+    heat_action:
+      - switch.turn_off: ac
+      - switch.turn_on: heater
+      - switch.turn_on: fan
+    idle_action:
+      - switch.turn_off: ac
+      - switch.turn_off: heater
+      - switch.turn_off: fan
+    default_preset: Home
+    preset:
+      - name: Home
+        default_target_temperature_low: 67 °F
+        default_target_temperature_high: 76 °F
+
+# display:
+#   - platform: ili9xxx
+#     model: ili9486
+#     dc_pin: GPIOXX
+#     reset_pin: GPIOXX
+#     invert_colors: false
+#     show_test_card: true