esphome:
  name: thermostat

esp32:
  board: esp32dev
  framework:
    type: arduino

# Enable logging
logger:

# Enable Home Assistant API
api:
  password: ""

ota:
  - platform: esphome
    password: ""

wifi:
  ssid: "Cochrun"
  password: "GreasyChicken784"

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "Thermostat Fallback Hotspot"
    password: "RUfAhbEfZmOU"

captive_portal:
    
i2c:
  sda: GPIO21
  scl: GPIO22
  scan: true
  id: bus_a

uart:
  tx_pin: GPIO27
  rx_pin: GPIO26
  baud_rate: 115200

sensor:
  - platform: bme280_i2c
    temperature:
      name: "Temperature"
      id: temperature
    pressure:
      name: "Pressure"
      id: pressure
    humidity:
      name: "Humidity"
      id: humidity
    i2c_id: bus_a
    address: 0x76

dfrobot_sen0395:

binary_sensor:
  # Information coming from uart bus
  - platform: dfrobot_sen0395
    name: Mmwave UART

    # on_...:
    #   - dfrobot_sen0395.settings:
    #       factory_reset: true
    #       detection_segments:
    #         # Define between one and four segments
    #         - [0cm, 3m]
    #         - [5.1m, 6.6m]
    #         output_latency:
    #           delay_after_detect: 0s
    #           delay_after_disappear: 0s
    #           sensitivity: 7

  # Information coming from dedicated gpio (IO2)
  - platform: gpio
    name: Mmwave GPIO
    device_class: motion
    pin:
      number: GPIO25
      mode: INPUT_PULLDOWN

switch:
  # Switch to turn on/off detection
  - platform: dfrobot_sen0395
    type: sensor_active
    name: Mmwave Active

  - platform: dfrobot_sen0395
    type: presence_via_uart
    name: Mmwave UART active
    restore_mode: always_on

  - platform: dfrobot_sen0395
    type: turn_on_led
    name: Mmwave Led
    restore_mode: always_on
    icon: "mdi:led-on"

  - platform: dfrobot_sen0395
    type: start_after_boot
    name: Mmwave Start
    restore_mode: always_on

  - platform: gpio
    pin: 16
    id: heater
    restore_mode: RESTORE_DEFAULT_OFF
  - platform: gpio
    pin: 17
    id: ac
    restore_mode: RESTORE_DEFAULT_OFF
  - platform: gpio
    pin: 15
    id: fan
    restore_mode: RESTORE_DEFAULT_OFF

climate:
  - platform: thermostat
    name: "Thermostat"
    sensor: temperature
    humidity_sensor: humidity
    min_cooling_off_time: 10s
    min_cooling_run_time: 10s
    min_heating_off_time: 10s
    min_heating_run_time: 10s
    min_idle_time: 30s
    cool_action:
      - switch.turn_off: heater
      - switch.turn_on: ac
      - switch.turn_on: fan
    heat_action:
      - switch.turn_off: ac
      - switch.turn_on: heater
      - switch.turn_on: fan
    idle_action:
      - switch.turn_off: ac
      - switch.turn_off: heater
      - switch.turn_off: fan
    default_preset: Home
    preset:
      - name: Home
        default_target_temperature_low: 67 °F
        default_target_temperature_high: 76 °F

# display:
#   - platform: ili9xxx
#     model: ili9486
#     dc_pin: GPIOXX
#     reset_pin: GPIOXX
#     invert_colors: false
#     show_test_card: true